Warning

You are reading the documentation for an older Pickit release (2.0). Documentation for the latest release (3.3) can be found here.

Getting ready for a remote software update

To receive an update of the Pickit software, your Pickit processor needs to be connected to the Internet:

  • The preferred method is to connect your Pickit processor via an Ethernet cable.

  • If this is not possible you can connect your Pickit processor via the 3G USB dongle.

Connecting via Ethernet cable

  1. Plug in an Ethernet cable (with Internet access) into the LAN port of the Pickit processor.

  2. Navigate to the Network settings, by clicking on the Settings button at the top-right of the web interface.

../_images/Settings-button-2.png
  1. In the Pickit port labeled ‘LAN’ section, make sure that the IP address field has a valid value (blue arrow in the image below).

../_images/Network-settings1.png

If an IP address shows up, you are good to go. A Pickit engineer can now connect to your system.

If no IP address shows up:

  • Double check if the Ethernet cable is attached in the right way to the Pickit processor and your network;

  • Check with your system administrator if there is a firewall on your network. If so:

    • Ask your system administrator to whitelist the ‘LAN’ port’s MAC address shown in the Network page. (red arrow in the image above)

    • Ask your system administrator to open TCP 443 port.

Note

Pickit uses VPN/TLS over TCP port 443 to establish a connection. The Pickit software update server is known as vpn.intermodalics.eu.

Connecting via USB dongle

Your Pickit system was delivered with a USB 3G dongle to connect the Pickit system to the Internet when connecting via Ethernet is not an option. A Pickit SIM card is already inside so this works out of the box.

Note

Since this is a wireless device, it’s important that it is positioned outside a metal enclosure (cage of Faraday). In case your Pickit system is in such an enclosure, you may use an extension cable up to 2m to install the remote service modem outside this enclosure.

Note

Depending on 3G reception on site, a Pickit support engineer could view and manipulate the Pickit web interface, install product and or setup files and perform updates. If the mobile reception is bad viewing and manipulating the interface could be impossible. On slow connections, software updates can take up to several hours.

Pickit systems were shipped with 2 different types of USB 3G dongles, use the images below as a reference to check which type of dongle came with your Pickit system.

Type 1

../_images/3g-dongle-type-1.jpg

The USB dongle can be plugged into any available USB port of your Pickit system. No configuration is required.

Status LED

Indication

Solid red

The modem is initializing.

Blinking red

Check if a SIM/USIM card is inserted. If it is, try to unplug and replug the modem.

Blinking green

The card has registered to the network but no Internet connection could be made. Try reinserting the USB modem and restarting the Pickit processor. If that doesn’t help, contact a Pickit support engineer.

Solid Green

The network is available with a successful Internet connection. A Pickit support engineer can now access the system.

Type 2

../_images/3g-dongle-type-2.jpg

The USB dongle can be plugged into any available USB port of your Pickit system. No configuration is required.

Status LED

Indication

Blinking green twice (every 3s)

The USB dongle is powered on.

Blinking green once (every 3s)

The USB dongle is registering with a 2G network.

Blinking blue (every 3s)

The USB dongle is registering with a 3G/3G+ network.

Solid Green

The network is available with a successful Internet connection to a 2G network. A Pickit support engineer can now access the system but the connection might be too slow to perform a software update.

Solid Blue

The network is available with a successful Internet connection to a 3G network. A Pickit support engineer can now access the system but the software update might take up to several hours.

Solid Cyan

The network is available with a successful Internet connection to a 3G+ network. A Pickit support engineer can now access the system to perform a software update.