Warning

You are reading the documentation for an older Pickit release (2.2). Documentation for the latest release (3.4) can be found here.

Yaskawa Pickit interface

This article documents the interface of the Yaskawa Pickit integration. For installation instructions, please refer to the Yaskawa installation and setup article.

Pickit macros

Below you find an overview of the macros defined by Pickit.

MACRO	Field name	Comment
MACRO1	PI_CALIB	Trigger a detection of the robot-camera calibration plate.
MACRO2	PI_LOOK	Trigger a Pickit object detection using the currently active setup and product Configuration.
MACRO3	PI_WAIT	Wait for Pickit reply with detection results. PI_WAIT should always be the next Pickit command after a PI_LOOK or PI_NEXT request.
MACRO4	PI_NEXT	Request the next detected object.
MACRO5	PI_CFG	Load the specified setup and product Configuration.
MACRO6	PI_SAVE	Save a Snapshots with the latest detection results.
MACRO7	PI_RUN	Check the current mode of Pickit.
MACRO8	PI_GPPD	Request the pick point ID and pick point offset of the last requested object.
MACRO9	PI_CAPTU	Trigger Pickit to capture a camera image to be used by a following PI_PROCE command.
MACRO10	PI_PROCE	Trigger an object detection on the camera image that was previously captured via PI_CAPTU command (or PI_LOOK).
MACRO11	PI_BUILD	Build the background cloud used in Advanced filters.

Tip

The ID’s of the macros can be changed by manually defining the Pickit macros. Note if the ID’s are changed the provided example programs by Pickit need to be altered accordingly.

Following macros have input arguments that need to be filled in when you call them.

PI_CALIB

• USER FRAME: User frame created at start of TEST_CALIB. By default, this is 5.

PI_CFG

• SETUP: Pickit setup file ID.

• PRODUCT: Pickit product file ID.

• USER FRAME: User frame that was created in TEST_CALIB. By default, this is 5.

• TOOL: Tool frame ID that is used by robot for picking.

• TIMEOUT: Value of the timeout used for communication with Pickit.

Note

If something is wrong here, you can expect the following message: Undefined user frame. The example program by default uses frame 5 and tool 1, but these might not exist.

Pickit registers

Below you find an overview of the variables used by Pickit. When using Pickit these variables cannot be used for anything else. More information about the variables can be found in Pickit socket interface.

Variable	Field name	Comment	Type
I049	command	command from robot to Pickit	Input
I048	setup	setup file ID known by the Pickit system	Input
I047	product	product file ID known by the Pickit system	Input
I046	Frame ID	frame ID used during calibration and picking	Input
I045	Tool ID	tool ID used for picking	Input
I044	Timeout	timeout used for communication with Pickit [ms]	Input
I042	pick_id	ID of the pick point that was selected for the given object	Output
I041	object_type	ID type of the detected object	Output
I040	status	Pickit status or a response to previously received robot commands	Output
I030-039	status of cycles	used for keeping track of the communication cycle with Pickit	Internal
S049	IP Pickit	IP address of Pickit, by default 169.254.5.180	Input
P049	object_pose	object pose expressed relatively to the robot base frame	Output
P048	object_dimension	[0]: length or diameter (m) [1]: width or diameter (m) [2]: height (m)	Output
P047	object_offset	pick point offset of the last requested object	Output
P046	rx_flip	helper pose to calculate a correct offset pose	Internal
D042	pick_ref_id	ID of the selected pick point’s reference pick point	Output
D041	object_remaining	number of remaining objects that can be sent in next messages to the robot	Output
D040	object_age	amount of time that has passed between the capturing of the camera data and the moment the object information is sent to the robot	Output

Tip

If these registers are already used on your robot, please contact us at support@pickit3d.com, and we will assist you in finding a solution.