Warning

You are reading the documentation for an older Pickit release (3.3). Documentation for the latest release (3.4) can be found here.

The Pickit Omron TM interface

Pickit integrates seamlessly with Omron TM cobots by means of a set of TMflow components, which add to the set of existing TM nodes. Each component is a building block for creating vision-guided applications with Pickit. This article documents the interface of the Pickit TM Components. For installation instructions please refer to the Omron TM Component installation and setup article.

The following sections describe the purpose of each component, the meaning of the input parameters (if any), as well as that of the output gateway states.

To insert a component instance into your robot program, click on one of the Pickit components listed on the left panel and drag it into your program. This is how Pickit components look like:

../../../_images/tm-interface-component-icon.png

Note

The naming convention for TMflow components is Application_Provider_Vendor_Version_Function, which for Pickit corresponds to perception_pickit_pickit_Vxx_Function. Pickit components only differ on the Function name, so throughout this article the common prefix is omitted for brevity.

A general note on introspecting component behavior is that the g_perception_pickit_user_msg global variable holds human-readable status updates from all components. For instance, when a component exists with an error state, the value of this variable can be shown in a Display node to get an insight on the failure reason. Refer to the pick and place example for the recommended usage.

System components

init

Initializes the connection with a Pickit system and handles communications with it. It should be the first Pickit component to appear in a robot program.

Parameters

  • Pickit IP address: It can be modified by editing the perception_pickit_pickit_V01_init1_pickit device of the internal send node:

../../../_images/tm-init-1.png ../../../_images/tm-init-2.png

Output

OK if robot mode has been enabled, ROBOT_MODE_DISABLED otherwise. Robot mode is enabled in the Pickit web interface, and is a requisite for performing picking operations, but not robot-camera calibration.

../../../_images/tm-init-3.png

Detection components

findObjects

Trigger a Pickit object detection using the currently active setup and product configuration.

The next Pickit component after findObjects should always be getResult, which waits until a response for the detection request is ready.

Tip

It’s valid (and sometimes encouraged) to perform robot motions or other non Pickit actions between calls to findObjects and getResult. For instance refer to the Example pick and place program for such an application.

Parameters

This component has no input parameters.

Output

OK if the object detection was successfully triggered, FAIL otherwise.

../../../_images/tm-findobjects-1.png

nextObject

Request the next detected object.

A single call to findObjects might yield the detection of multiple objects. nextObject allows to request the next available object, if any, without the need of triggering a new detection and the time overhead it entails.

The next Pickit component after nextObject should always be getResult, which waits until a response for the request is ready.

Tip

It’s recommended to use this component only when objects in the detection region have not moved (significantly) since calling findObjects. A good example of when to use nextObject is when a detection is unreachable by the robot.

Parameters

This component has no input parameters.

Output

OK if there is a next detected object, FAIL if the set of detected objects has been exhausted.

../../../_images/tm-nextobject-1.png

getResult

Wait for Pickit reply with detection results. This should always be the next Pickit component after a findObjects or getNextObject request. It blocks the robot until a reply from Pickit is received. When an object has been found, the following global variables are populated:

  • g_percepton_pickit_pose Object pick pose.

  • g_percepton_pickit_dim Object dimensions.

  • g_percepton_pickit_type Object type.

  • g_percepton_pickit_remaining_obj Number of remaining object detections from the last call to findObjects. After first calling getResult, this variable contains the total number of object detections minus one. This value is also equal to the number of times getNextObject can be called. As such, the value decreases with each call to getNextObject.

Parameters

This component has no input parameters.

Output

Pickit can discriminate the following scenarios, for which the robot program can take action upon:

  • OBJECT_FOUND: A valid object has been found.

  • NO_OBJECT_FOUND: There are no pickable objects, yet the Region of Interest (ROI) is not empty.

  • EMPTY_ROI: There are no pickable objects because the ROI is empty.

  • NO_IMAGE_CAPTURED: Image capture failed, most probably due to a disconnected camera.

  • FAIL: The call to getResult failed, for instance because it was called at the wrong place (not the next Pickit component after a findObjects or getNextObject request).

../../../_images/tm-getresult-1.png

Warning

As of version 1.72 of TMflow, it is not possible to programmatically check if a pose is reachable by the robot before it gets executed. It is currently recommended that end users focus on applications in which parts are known to be always reachable. When parts can overlap, as in bin picking scenarios, the methods below help in making sure that objects are reachable.

  • For suction and magnetic grippers that exhibit compliant behavior, add flexible pick orientation to the robot tool.

  • For fingered grippers, ignore parts that are too tilted. This setting is also in the Picking tab, under Collision prevention. Set the maximum angle to a low value such as 15 degrees.

Configuration components

configure

Loads a specified setup and product configuration. This specifies the behavior of Pickit detections, i.e. where and what to look for.

Parameters

By default, the IDs correspond to invalid values, so it is required to edit these parameters.

../../../_images/tm-configure-1.png

Output

OK if the requested configuration was successfully loaded, FAIL otherwise. The most typical failure reason is specifying non-existent IDs.

../../../_images/tm-configure-2.png

buildBackground

Build background cloud used by some advanced Region of Interest filters. This is an advanced feature, rarely triggered from the robot program in practice.

Parameters

This component has no input parameters.

Output

OK if the background cloud was built, FAIL otherwise.

Calibration components

findCalibrationPlate

Trigger detection of the robot-camera calibration plate. This component requires the Pickit web interface to be in the Calibration page.

This component is meant to be used only in robot-camera calibration programs such as the Example calibration program. It is not meant to be used in picking programs.

Parameters

This component has no input parameters.

Output

OK if the calibration plate was found, FAIL otherwise.

../../../_images/tm-findcalibrationplate-1.png

Monitoring components

saveSnapshot

Save a snapshot with the latest detection results. The saved snapshot can then be loaded or downloaded by going to the Snapshots page on the Pickit web interface and searching for a file whose name contains the capture timestamp.

Parameters

This component has no input parameters.

Output

OK if the snapshot was successfully saved, FAIL otherwise.

../../../_images/tm-savesnapshot-1.png